Hear from Our Customers
You’re not cutting material for fun. You need parts that meet spec, edges that don’t need rework, and turnaround times that keep your project moving.
Waterjet cutting services in Westbury, NY give you that. No heat-affected zones that warp metal or change material properties. No hardened edges that crack under stress. No secondary finishing that eats into your timeline and budget.
The abrasive waterjet cutting process handles everything from eighth-inch aluminum to six-inch stainless steel with the same setup. Intricate curves, sharp corners, nested parts—all cut with a stream thinner than a pencil lead. Your CAD file goes in, and finished parts come out ready to install or assemble.
Architects working on Long Island projects use this for custom metal panels and decorative inlays. Fabricators rely on it for brackets and structural components that can’t have burn marks or warping. If you’re dealing with composites, laminates, or materials that traditional cutting methods destroy, this is how you get usable parts.
We work with architects, designers, contractors, and fabricators across Westbury, NY and the broader Long Island area. We’re not a general machine shop that does waterjet cutting on the side—this is what we do.
From concept to completion, we handle custom design consultation, material selection, and precision cutting. Long Island’s aerospace and medical manufacturers count on us for technically challenging jobs with tight tolerances. If you’re working on a feature wall in a Westbury office building or need performance parts for a restoration project, you’re getting the same attention to detail.
We’ve built our reputation on solving problems that other shops turn away. Complex geometries, thick materials, mixed composites—if you can draw it, we can cut it.
You send us your design file—DXF, DWG, or even a sketch if that’s what you’re working from. We review it for any potential issues with tolerances, material selection, or nesting efficiency. If something won’t work as drawn, we tell you before we start cutting.
Once the file is dialed in, we load your material onto the cutting table. Our high pressure water cutting system in Westbury, NY runs at 60,000 PSI, mixed with garnet abrasive for harder materials. The stream follows your design path with CNC precision, making cuts that hold tolerances down to ±0.003 inches.
There’s no heat, so there’s no warping or material distortion. No tool changes between materials—the same stream cuts rubber gaskets and hardened steel plate. The process is cold, which means your material properties stay intact from edge to edge.
After cutting, parts come off the table with smooth edges. Most applications don’t need deburring or secondary finishing. You get parts that are ready to use, not halfway there.
Ready to get started?
Every custom waterjet cutting project in Westbury, NY includes material consultation before we start. Not sure if your design works better in aluminum or stainless? We’ll walk through the options based on your application, budget, and timeline.
We handle material sourcing if you need it, or we’ll cut from your supplied stock. Nesting optimization is standard—we arrange parts to minimize waste and keep your material costs down. For Long Island contractors working on commercial builds, that efficiency matters when you’re cutting dozens of panels or components.
You get CNC precision on every cut, whether it’s a single prototype or a production run. The abrasive waterjet cutting process in Westbury, NY doesn’t slow down for complexity. Intricate logos, tight radiuses, nested parts with minimal spacing—it’s all the same to the machine.
Turnaround depends on material thickness and job size, but most projects move faster than you’d expect. We’re not waiting for tooling or setup changes between materials. One job might be stone inlays for a Westbury lobby, the next could be titanium aerospace components. Same machine, same precision, different materials.
Virtually anything. Metal, stone, glass, composites, plastics, rubber, foam, wood—if it’s a solid material, waterjet cuts it.
The process doesn’t rely on hardness or heat tolerance. We’ve cut everything from soft gasket material to hardened tool steel, often in the same day. Aluminum composite panels, rubber-lined wear plates, bonded laminates—materials that would delaminate or melt with traditional cutting methods come out clean.
Thickness isn’t a limiting factor either. We’ve cut eighth-inch acrylic for signage and six-inch stainless plate for structural components. The stream adjusts for material density, not thickness. For Westbury projects that mix materials—like architectural installations with metal, stone, and glass elements—you’re not coordinating between multiple fabricators. One process handles all of it.
Tolerances hold to ±0.003 inches on most materials. That’s tighter than plasma and comparable to laser, but without the heat distortion that throws off laser-cut parts when they cool.
Laser cutting generates a heat-affected zone that can warp thin materials or change the molecular structure near the cut edge. Plasma is fast but rough—you’re looking at secondary finishing on almost every part. Waterjet cutting services in Westbury, NY give you precision without those tradeoffs.
The CNC system follows your design path exactly. There’s no kerf compensation guesswork, no edge bevel from heat, no hardened zones that crack under stress. For parts that need to fit together with minimal clearance—brackets, flanges, interlocking panels—waterjet delivers the accuracy you’re actually paying for. Long Island fabricators working on aerospace or medical components use this specifically because the tolerances don’t drift.
Most parts come off the table ready to use. The cutting stream produces a smooth edge with no burn marks, no slag, and minimal burring.
You’re not dealing with the melted material buildup that plasma leaves behind, or the oxidized edges from laser cutting. The abrasive waterjet cutting process in Westbury, NY is a cold cut—material is eroded away, not melted or burned. That means the edge quality is consistent from start to finish.
Thicker materials might have slight burring on the bottom edge, but it’s nothing like what you’d see with torch cutting or even some laser work. For most applications—architectural panels, machine parts, decorative elements—parts go straight from our table to your assembly or installation. That’s time saved and cost eliminated. If your project does require a specific edge finish, we’ll tell you upfront what to expect and what secondary work might be needed.
It depends on material thickness, complexity, and quantity, but most jobs move faster than traditional cutting methods because there’s no tooling or setup changes between materials.
A simple part in quarter-inch aluminum might take minutes. Intricate designs in two-inch stainless could take hours. The difference is that we’re not stopping to change tools, adjust feeds and speeds, or wait for cooling cycles. Our high pressure water cutting system in Westbury, NY runs continuously through your entire job.
For production runs, nesting efficiency makes a big difference. We can pack multiple parts onto a single sheet with minimal spacing, cutting them all in one pass. That’s faster than indexing individual parts or dealing with remnant material that’s too small to reuse. If you’re a Westbury contractor working against a tight installation deadline, we’ll give you a realistic timeline upfront—not a best-case estimate that slides when complications show up.
Yes to both. The process isn’t limited by thickness the way laser or plasma cutting is, and the narrow cutting stream handles curves and corners that would require multiple setups with traditional machining.
We’ve cut six-inch steel plate and intricate scrollwork in the same week. The stream diameter stays consistent regardless of material thickness—you’re getting the same precision on thick stock as you would on thin sheet. That matters for structural components, heavy brackets, or any application where you can’t compromise on accuracy just because the material is thicker.
Complex shapes are where waterjet really separates itself. Sharp inside corners, tight radiuses, nested parts with minimal clearance—all possible without tool changes or repositioning. For custom waterjet cutting in Westbury, NY, that means your architectural details, decorative metalwork, or performance parts come out exactly as designed. No simplified geometry to accommodate tooling limitations. If you can model it, we can cut it.
Because you need parts that don’t warp, edges that don’t need rework, and materials that can’t handle heat. Traditional machining has its place, but waterjet solves problems that drills, saws, and torches create.
There’s no heat-affected zone changing your material properties. No hardened edges that crack under load. No tool wear that degrades accuracy halfway through a production run. The waterjet cutting process in Westbury, NY maintains the same precision from the first part to the last, regardless of material hardness.
You’re also not limited to straight cuts or simple geometries. CNC waterjet handles curves, angles, and intricate patterns without multiple setups or specialized tooling. For Long Island projects mixing materials—stone inlays with metal frames, composite panels with decorative cutouts—you’re not coordinating between a stone saw, a metal shear, and a router. One process, one setup, one fabricator. That’s fewer variables, faster turnaround, and parts that actually fit together the way your design intended.
Local Resources
Useful Links
Other Services we provide in Westbury
